Frequent, often different, BSODs while computer comes under load.

Hello! I have been trying to debug this myself for a while, and I'm rather at my wit's end here. I've been experiencing very frequent BSODs every time the computer comes under any sort of load, however it may take a while for them to start happening. Once they start happening, it seems to come more frequently. I've seen Clock Watchdog Timeout, WHEA, IRQUL NOT LESS OR EQUAL, SYSTEM SERVICE EXCEPTION, KMODE EXCEPTION NOT HANDLED, SYSTEM THREAD EXCEPTION NOT HANDLED, among others I cannot remember. These have been happening ever since I did my clean install of Windows 10 preview, and have persisted through each update until now. I also experience freezing during load as well, though that is rarer, and only seems to happen during gaming, whereas the BSODs will happen while closing startup programs, copying files, or any other activity that puts stress on the computer.

I have included the dxdiag, and I dearly hope you wonderful people here can help me out on this as you've helped me with other issues through other people's solved problems.

• WIN-OVIIP6CIK8K-Tue_08_25_2015_162932_38.zip (1.83 MB, 2 views)

Hi AsteriaNox,

I couldn't find much in the dump files, so I want to make sure the drivers are tested.

Diagnostic Test

 DRIVER VERIFIER

   Warning

Please make a backup of your important files and get your rescue media or create one.
Please create a restore point.

Please read and run driver verifier.

Driver verifier stresses your drivers and will crash your pc if any driver fails due to a violation.

If driver verifier has found a violation and you can't get back into windows normally, try to boot into safe mode and reset in safe mode driver verifier, or in the troubleshooting options open command prompt and type verifier /reset.

   Note

Your system will act very sluggishly while driver verifier is enabled, this is normal as your drivers will be being subjected to heavy testing in order to make them crash.

Ok, I ran the verifier, and upon restart it crashed. I've uploaded my minidumps again and they are attached to this reply.

While I was in safe-mode after doing the verifier reset, I did an sfc /scannow and dism /online /cleanup-image /restorehealth

Neither came back with anything.

• minidumps.zip (1.52 MB, 1 views)

There is 1 driver that came out of the dumps, the Wacom HID Router Driver
Please check for windows 10 compatible updates here

Code:

6: kd> lmvm wachidrouterstart             end                 module name fffff801`49c60000 fffff801`49c7e000   wachidrouter T (no symbols)                Loaded symbol image file: wachidrouter.sys     Image path: SystemRootSystem32driverswachidrouter.sys     Image name: wachidrouter.sys  Timestamp:        Tue Apr 28 19:05:14 2015(553FBDCA)     CheckSum:         0002443F     ImageSize:        0001E000     Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4

That driver was installed just within the last couple days, and these problems have all persisted for months. Should I run Driver Verifier again?

I would need you to do a couple of hardware tests starting with the RAM.

Please Run Memtest86+

   Information

Please download from this site only in the middle of the page are the Download links, you can download the ISO.zip or the Auto USB Flash Drive installer.zip

Extract the Zip file. If you chose the ISO image, burn it to a CD using Windows Disk Image Burner or any Image burner you may have. If you downloaded the Auto USB installer, extract it, insert your USB 2.0 Flash Drive and take note of the drive letter. Run the installer, select the Flash Drive Letter, check the format box and press next. It will install memtest86+ to a flash drive. You can use either V4.20 or V5.01. Boot from your selected media. If you use V5.01 it will tell you to press certain buttons at the start, please press no buttons. The test will begin on it's own and continue to run until you stop it. It needs to run for 8 complete passes or until you receive an error. If you receive an error, stop the test. Even 1 error is a fail. Each pass tests a different part of the ram and each of the 10 tests in each pass tests something different. It takes a minimum of 8 passes in the same session to completely test the ram, more passes are better. It is quite a long test and will take several hours depending on how much ram you have. Due to the time length it is best to run overnight. If you have any questions, please do not hesitate to ask.